Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
Every person may have their own way of thinking when it comes to Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old tub is easily obtainable, the project can move rapidly; if you need to open a wall to get rid of the old tub as well as place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new bath tub in your washroom if you have actually currently bought a new tub and don't need to change the arrangement of your previous supply of water pipelines.
Your devices and also product checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome as a result of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will come from the pipes. When the supply pipelines have actually been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the supplier supplied backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level as well as adjusting the feet on the tub till the spirit level reviews level.
To set up taps, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Load the bathtub as well as also inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub should wait until the tub has actually been used a minimum of when as this will certainly settle it into its last placement.
Preparing for the Installation
First of all, the sustaining framework provided with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, creating the water to pass through the wall surface in between the bath and the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and installations. They are marketed in tubes and also cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to permit the motion experienced when the tub is in usage. The sealer can split relatively early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly offered on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that content about Installing A Bathtub when perusing the internet. Sharing is good. One never knows, you may very well be helping someone out. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Browse Our Site
Report this page